Battery Changing Tools & Supplies

Is a selection of India made tools that are not very good. Supplied with pouch to hold tools. The two most important items, the snap back case knife and the screw back case opener might last a day or two or perhaps break on the first try. If you need tools to open the back of cases then you must buy a few decent tools. Battery changing can generate a great deal of revenue and if only makes sense to invest some money into decent tools that will both do the job and last many years.
 

Stainless Steel Screws, organizied in a 24 bottle assortment of different sizes. Thread diameters .70, .80, .90, 1.00, 1.20 and 1.40 mm in different lengths and head styles.

CS360
$88.00
 

This is the standard case holder in the industry, and is the best by far. Made of a hard nylon material that will not break, and since it is nylon, it will not mark the case. The four pins are adjustable to hold a small ladies cases to all but the most monster sizes of the men's cases, which are over 44 mm in diameter. This will hold cases up to 44 mm diameter. Once you have the case locked into the Bergeon 5090 case holder, you now have to tighten the 5090 in a your shop vise. Locked in place in your shop vice you can now use two hands when using a case wrench to open the case back.

FB-200
$46.95
 

This Jaxa case holder is for the really big ones. As you can see, it can hold a much larger watch than the one shown in the photo. If the big ones cross your bench, then you know you need one of these. You can put cases up to 66 mm in diameter in this holder and if you had to hold an 18 mm diameter case, well you can still use this extra holder.

FB-202
$104.00
 

Each chuck is adjusted by its own knob, which allows a firm hold and whatever you need to get a firm hold on. Place it in a vice or use it on your bench top. The chucks are the same hard nylon used in the Jaxa holders while the body is made of steel. Will hold cases up to 43 mm in diameter.

FB-232
$99.95
 

Everybody needs a case holder which is placed in the jaws of your case vise. This Beregon case holder is very well made, and holds both ladies and most gents watches.

FB-205
$24.95
 

This Swiss-made Bergeon case holder is for watches with lug widths of 15, 16, 17, 18, 20, and 22 mm. Held in bench vice. made of plastic material which cannot scratch the cases.

FB-204
$41.90
 

This Swiss-made Bergeon case holder is for watches with lug widths of 8, 9, 10, 11, 12, and 14 mm. Held in bench vice. made of plastic material which cannot scratch the cases.

FB-203
$37.40
 

The MSA06.135 press is packaged with 43 screw-on threaded metal center delrin nylon dies. Everything you need to replace bezels, snap case backs closed, and install mineral crystals, waterproof tension ring and divers crystals. The MSA06.135 press does not have the screw control found on the MSA06.150 press with screw control.

MSA06.136
$579.00
 

The "BB" crystal press will work with all "BB" snap-on dies that are included. Complete with 10 double sided tapered wall aluminum dies and 3 flat fixtures.

BB-502B
$185.00
 

Plastic jaws, spring loaded with locking nut.

180.382
$9.90
 

This is a must own tool for anyone that changes batteries but does not repair watches. When it beeps before you open the watch you know that the watch needs more than just a new battery.

W3000
$49.99
 

This watch analyzer llows users to tell whether the step motor is working or if the battery is dead - without opening the watch. Unlike competitive testers at a higher price, this analyzer will test the coil as well. This compact unit is a great tool for watchmakers and jewelers as well as department stores. 9 volt battery included

BAT-200.00
$39.95