Case 10 ATM Steel, 42mm with Top & Bottom Mineral Glass| | Case Style #17 comes with a brass nickel plated movement ring, which allows the case to be used with the ETA 2801-2, 2804-2, 2824-2, 2836-2, Sellita SW200-1, SW210-1, SW220-1 movements.
This 10 ATM water resistant case is made of 100% stainless steel, has a hardened 35.50 mm diameter x 2.30 mm thick mineral glass on top, hardened 25.00 mm diameter x 1.30 mm thick mineral glass on bottom and 7 mm waterproof crown (tube size 2.50 mm). The watch band lug size is 22 mm. Case diameter is 42 mm with a height of 11.65 mm. This case take a dial with an outside diameter of no more than 35.8 mm the viewable dial opening is 35 mm. The distance from the case lug holes on one side to the other is 46 mm (1 13/16 inch).
THIS IS A COMPLETE CASE! All complete cases will come with Crystals, Crown and all Gaskets.
In separate bag is the movement case ring, a tension spring that fits in the case back and a O-ring case back gasket. The case ring is installed with the flat side down (the cut out should go over the stem) after the movement has been set inside the case. No case clamps are needed with this design, however the movements case screws are needed and screwed in so they make contact with the case ring. Place the tension spring on the inside of the case back before screwing the case back onto the case.
Click here to see Assembly Instructions for 42 mm Cases 12 thru 17.
| |
OFREI-CASE17
$75.95
|
Case 10 ATM Steel, 42mm with Top & Bottom Mineral Glass and Screwdown Crown| | Case Style #15 comes with a brass nickel plated movement ring, which allows the case to be used with the ETA 2801-2, 2804-2, 2824-2, 2836-2, Sellita SW200-1, SW210-1, SW220-1 movements.
This 10 ATM water resistant case is made of 100% stainless steel, has a hardened 35.50 mm diameter x 2.30 mm thick mineral glass on top, hardened 25.00 mm diameter x 1.30 mm thick mineral glass on bottom and 7 mm screwdown crown. The watch band lug size is 22 mm. Case diameter is 42 mm with a height of 11.65 mm. This case take a dial with an outside diameter of no more than 35.8 mm the viewable dial opening is 35 mm. The distance from the case lug holes on one side to the other is 46 mm (1 13/16 inch).
THIS IS A COMPLETE CASE! All complete cases will come with Crystals, Crown and all Gaskets.
In separate bag is the movement case ring, a tension spring that fits in the case back and a O-ring case back gasket. The case ring is installed with the flat side down (the cut out should go over the stem) after the movement has been set inside the case. No case clamps are needed with this design, however the movements case screws are needed and screwed in so they make contact with the case ring. Place the tension spring on the inside of the case back before screwing the case back onto the case.
Click here to see Assembly Instructions for 42 mm Cases 12 thru 17.
| |
OFREI-CASE15
$78.95
|
Case 10 ATM Steel, 42mm with Top & Bottom Sapphire Glass| | Case Style #14 comes with a brass nickel plated movement ring, which allows the case to be used with the ETA 2801-2, 2804-2, 2824-2, 2836-2, Sellita SW200-1, SW210-1, SW220-1 movements.
This 10 ATM water resistant case is made of 100% stainless steel, the top Sapphire glass is has a 35.50 mm diameter x 1.80 mm thick sapphire glass on top, 25.00 mm diameter x 1.30 mm thick sapphire glass on bottom and 7 mm waterproof crown (tube size 2.50 mm). The watch band lug size is 22 mm. Case diameter is 42 mm with a height of 11.10 mm. This case take a dial with an outside diameter of no more than 35.8 mm the viewable dial opening is 35 mm. The distance from the case lug holes on one side to the other is 46 mm (1 13/16 inch).
Sapphire Glass Crystals On Front And Back
THIS IS A COMPLETE CASE! All complete cases will come with Crystals, Crown and all Gaskets.
In separate bag is the movement case ring, a tension spring that fits in the case back and a O-ring case back gasket. The case ring is installed with the flat side down (the cut out should go over the stem) after the movement has been set inside the case. No case clamps are needed with this design, however the movements case screws are needed and screwed in so they make contact with the case ring. Place the tension spring on the inside of the case back before screwing the case back onto the case.
Click here to see Assembly Instructions for 42 mm Cases 12 thru 17.
| |
OFREI-CASE14
$104.50
|
Case 10 ATM Steel, 42 mm Top and Bottom Sapphire Glass with Screwdown Crown| | Case Style #16 comes with a brass nickel plated movement ring, which allows the case to be used with the ETA 2801-2, 2804-2, 2824-2, 2836-2, Sellita SW200-1, SW210-1, SW220-1 movements.
This 10 ATM water resistant case is made of 100% stainless steel, has a 35.50 mm diameter x 1.80 mm thick sapphire glass on top, 25.00 mm diameter x 1.30 mm thick sapphire glass on bottom and 7 mm screwdown crown. The watch band lug size is 22 mm. Case diameter is 42 mm with a height of 11.10 mm. This case take a dial with an outside diameter of no more than 35.8 mm the viewable dial opening is 35 mm. The distance from the case lug holes on one side to the other is 46 mm (1 13/16 inch).
Stainless Steel, Sapphire Glass and 10 ATM Water Resistant
THIS IS A COMPLETE CASE! All complete cases will come with Crystals, Crown and all Gaskets.
In separate bag is the movement case ring, a tension spring that fits in the case back and a O-ring case back gasket. The case ring is installed with the flat side down (the cut out should go over the stem) after the movement has been set inside the case. No case clamps are needed with this design, however the movements case screws are needed and screwed in so they make contact with the case ring. Place the tension spring on the inside of the case back before screwing the case back onto the case.
Click here to see Assembly Instructions for 42 mm Cases 12 thru 17.
| |
OFREI-CASE16
$112.95
|
Case 10 ATM Steel, 42mm with Mineral Glass, Screwdown Crown and Solid Stainless Steel Case Back| | Case Style #12 comes with a movement ring, which allows this case to be used with the ETA 2801-2, 2804-2, 2824-2, 2836-2, Sellita SW200-1, SW210-1, SW220-1 movements.
This 10 ATM water resistant case with 42 mm outside diameter is made of 100% stainless steel. The Crystal is a hardened 2.30 mm thick mineral glass 35.50 mm diameter. The case back is solid 100% stainless steel case back and features a 7 mm screwdown crown. The watch band lug size is 22 mm. The height of this 42 mm diameter case us only 11.65 mm. The dial needed for this case can be no more than 35.8 mm outside diameter. The viewable dial opening the part that can be seen is 35 mm. The distance from the case lug holes on one side to the other is 46 mm (1 13/16 inch).
Solid Stainless Steel Back 10 ATM Water Resistance
THIS IS A COMPLETE CASE! All complete cases will come with Crystals, Crown and all Gaskets.
In separate bag is the movement case ring, a tension spring that fits in the case back and a O-ring case back gasket. The case ring is installed with the flat side down (the cut out should go over the stem) after the movement has been set inside the case. No case clamps are needed with this design, however the movements case screws are needed and screwed in so they make contact with the case ring. Place the tension spring on the inside of the case back before screwing the case back onto the case.
Click here to see Assembly Instructions for 42 mm Cases 12 thru 17.
| |
OFREI-CASE12
$69.95, On Sale $64.95
|
Luminous Numbers & Hour Markers, Dial w/24 Hr Track Black for 2836-2 & SW220-1| |
Dial for our 42 mm diameter 10ATM Watch Cases Style #'s 12 thru 18. The outside diameter of this dial is 35.8 mm, it is 29.0 mm to the start of the minute track, 31.0 mm to the end of the minute track minute track and 34 mm to the end of the 60, 05, 10 etc. outer ring of numbers. Dial fits the ETA 2836-2 or Sellita SW220-1 Swiss Made day/date movements .
| |
DIAL-35.8-#3
$12.00
|
Luminous Numbers & Hour Markers, 35.8 mm Dial w/24 Hr Track Black for Sellita SW210-1 & ETA 2801-2| |
Dial for our 42 mm diameter 10ATM Watch Cases Style #'s 12 thru 18. The outside diameter of this dial is 35.8 mm, it is 29.0 mm to the start of the minute track, 31.0 mm to the end of the minute track minute track and 34 mm to the end of the 60, 05, 10 etc. outer ring of numbers.
| |
DIAL-35.8-#1
$12.00
|
Extra Long 20 mm Stem for Sellita SW210-1|
|
Also for Sellita SW200-1, SW215-1, SW220-1, SW240-1 & SW260-1. Also interchangeable with ETA stem series 2801-2 etc. If your going to re-case or casing a movement into a 42 mm or larger case, a this 20 mm long stem may be necessary. A standard 16 mm long stem comes installed by the factory on all new movements.
| |
401/1543-SEL
$4.95
|
SELLITA Swiss Made SW210-1 Incabloc 19 Jewels Special Elaborate Version Watch Movement| | The SELLITA SW210-1 is an improved clone version of the obsolete ETA 2801-2 movement. This manual handwinding 11.5 ligne movement, with 19 jewels features special elaborate 3 position regulation (CH, 6H, 9H, +/- 7 s/d) and the deluxe Incabloc shock system. Plates are Nickel with standard Sellita finish. Most parts are interchangeable with the ETA 2801-2. Hand sizes Minute 0.90 mm, Hour 1.50 mm and sweep 0.25 mm. 28,800 BPH, lift angle of balance 50, Amplitude Max. (CH oh) 320, Min. (6H 24h) 200.
Click here to download the SELLITA SW210-1 technical sheet and oil chart.
| |
SELLITA-SW210-1
$148.00
|
Sunken Dial with Groves White-Green Luminous 35.8 mm fits Cases #12-18, for ETA 2824-2
| |
Dial Diameter 35.8 mm, minute track is 34 mm. For our 42 mm cases styles #12, #13, #14, #15, #16, #17 and #18 with the ETA 2824-2 or Sellita SW200-1 movement with date window.
| |
DIAL-35.8-#4
$12.00
|
O-Ring Gaskets GK-75-3800
$2.10
Cross Section: 0.75 mm, Inside Diameter: 38.00 mm. Sold in packages of 3 pieces, price breaks at 6, 12 and 144 packages.
|
Hands, 90/150/25 For Large Diameter Watch Dials
Selection of long length hands to fit our 42 mm cases and large diameter dials in the popular hole size, minute 0.90, hour 1.5 and second 0.25 mm.
|
Dials to Fit 42 mm 10ATM Cases Styles 12 thru 17
|
Assembly Instructions for 42 mm Cases 12 thru 17
|
Replacement Parts, 42 mm Cases For SELLITA and ETA Mechanical Watch Movements
|
