Bergeon Balance Holder 30106| | Tool with holes for balances in nickel-plated brass and is 35 mm in diameter. | |
FB-130
$41.20
|
Bergeon Delrin Balance Holder 30106-D| |
Tool with holes for balances in Delrin and is 36 mm in diameter.
| |
FB-130-DELRIN
$52.78
|
Bergeon 2810 Roller Remover| |
Everyone needs one of these Bergeon roller removers.
| |
BERG-2810
$24.00
|
Bergeon 4852 Roller Remover Vydiax| |
Who says new tools are not being developed for Watchmakers. This Bergeon tool is very good and has only been on the market for a few years. For turning and removing rollers, made in nickle plated brass.
| |
FB-711
$69.50
|
Bergeon 4854 Cannon Pinion Remover with Lever and Wooden Handle| |
For small and large watches, adaptable to all sizes
| |
FB-741
$88.00
|
Bergeon Collet Closing Tool 3007| | Seven different notches for closing collets. | |
BERG-3007
$139.00
|
Bergeon Roller Remover 30070| | Roller seat fits in the "V" slot, use slight pressure on the punch and the roller is removed. | |
30070
$106.10
|
Bergeon 5482 Pivot Rounder| | The rounding part of the tool is jewelled and should be used with a lubricant. I've heard others say that this tool can be used with Diamantine or similar product to round the tips of balance pivots.
| |
5482
$65.00
|
Balance Tack| | Just slip the cock over the pin tip with the balanced still attached. A balance tack is a fast and simple holder of collet that everyone should have.
| |
FB-105
$15.25
|
Bergeon 6887 Stud Holder| |
This New Bergeon Stud Holder is top of the line. A very helpful tool when when fitting a new hairspring stud. Dimensions: 40 x 46 mm.
| |
BERG-6887
$212.00
|
Stud Holder| | Stud fitting tool, made of tempered steel of excellent quality. A very helpful tool when when fitting a new hairspring stud.
| |
FB-173860
$158.00
|
Bergeon Levers for Balance Cock 5432-A| | Handle in plastic. 
| |
5432-A
$56.50
|
Bergeon Levers for Balance Cock 5432-B5432-B
$56.50
|
Broaches For Hairspring Collet 0.50 mmMSA03.101-05
$29.60
|
For Turning and Setting Hairspring Collets 1.10 mm.| |
nickel-plated brass knurled handle. Hole diameter: 0.45 mm. length: 95 mm.
| |
MSA03.102-11
$45.00
|
Bergeon 30207 Studding Table| |
This very useful tool holds the balance spring stud when re-studding a spring. It can also be used for a variety of other holding tasks for small parts. This table is not only useful, but beautifully made.
| |
FB-2835
$169.00
|
Bergeon 3010 Tube-Tightener Set in Wood| |
Bergeon tool for tightening crown, case and hand tubes. This is the correct way to tighten any tubes between 0.40 to 2.60 millimeters.
In wooden case. With 18 interchangeable collets and 1 lever. The pipes are tightened evenly over their entire circumference. This ensures that they fit firmly and evenly on the hand arbor or crown.
| |
FB-715
$589.00
|
Bergeon 2677 "Platax" Roller & Staff Remover| | The Bergeon - Platax Roller and staff remover 2677, contains 3 staff removing punches (.10, .15, .20 mm), one center punch, 3 heeled bushes (.90, 1.10, 1.40 mm), on a wooden base. | |
FB-735
$488.00
|
Click Here For Replacement Parts for the Bergeon 2677 "Platax" Roller & Staff Remover
|
ETA Chron Stud Removing Tool| | Has small fork shaped tip for removing the stud block. Overall length: 2.25 inches.
| |
AF-015600
$34.95
|
ETA Chron Regulator Adjusting Tool| | Has small opening at the tip for adjusting the regulator pins. Overall length: 2.25 inches.
| |
AF-015595
$34.95
|
Bergeon 4 in 1 Tool| | Very simple to use. Can be fixed inside a vice.
| |
BERG-4001
$622.00
|
Click Here to View Replacement Parts for the Bergeon 4 in 1 Tool
|
Your cooperation is appreciated.
|
Bergeon Polystyrene Red Stick| | Polystyrene stick with pointed end on one side and flat end on the other. Length is 135 mm with 4 mm diameter.
| |
BERG-6436
$2.96
|
